Digiprog 3 2014 manuals Link attached. Do not forget about + Attached Files. 889 77 bytes Download. Thanks given by: sendreq, Mario3, Buntingford. Digiprog 3 digiprog III car list and user manual. 1)DIGIPROG 3 password is 1 2)Language: Digiprog 3 DVD is German, but the operation is available with both English and German, after you turn on Digiprog 3, click 'language' option, and then set English 3)Cannot connect with internet except update. Www.digiprog.com © 2007 by DigiProg Ltd INTRODUCTION Page 5 3. Motorcycle Menu This menu is the same as the CAR/TRUCK menu but is used for.

Confirmed! Digiprog 3 odometer correction tool for EEPROM data reading

I need digiprog3 manual, to connect citroen c5 2011 bsi? If i helped click thanks and add reputation. Thanks given by: Reply. Kamaleon Location Offline V.I.P Reputation: 8,875. Thanks Given: 14120 Thanks Received: 22821 (5920 Posts) Posts: 6,681 Threads: 122 Joined: Jan 2014.

You have to know:

On some vehicles, you may see an eight-pin EEPROM chip that is used to store vehicle data and these chips capture vital vehicle information such as ignition and immobilizer codes. Once you lose this data, it can cause anything from a minor fault to major flaws and even do you need to fix your machine, so it’s very important to use the digiprog3 “EEPROM” menu to read and save the original information.

The EEPROM chip would have a number on top of itself and in general it will be “93C46”, you can connect it to your Digiprog III via ST1 or ST4 adapter. Then you must tell your Digiprog III which chip you are working on before using it to read.

Tutorial: How to use Digiprog 3 to read data of EEPROM

Digiprog 3 V4.94

1. De-solder the EEPROM chip;
2. Check the contact points or legs with fiberglass pin all the way in;
3. Clearly clean with sandpaper;
4. Insert EEPROM correctly into Digiprog3 ST01 / ST04 adapter, and make sure they are in good contact;
5. Connect a DP3 device to your car via the OBD connector
6. Enter the “EEPROM” menu

7. Read the EEPROM data and store it in digiprog3; Follow this way:

Select the “TYPE SET” and choose “93C46”, then your Digiprog has been set up to read a 93C46 chip. Press “EEPROM” again, then “READ”. It will show you the information on the Digiprog III screen when playback is complete. Now, press “check” if the information on your screen may agree with the Eeprom.

Then click on the “File” and it will show you another submenu, you can click “Save” and enter a file name for the information you save. Once you have entered the file name, your data is safe and the vehicle is now ready to be reprogrammed.

8. Get ST01 EEPROM / ST04 adapter and recharge it;
9. Select the EEPROM COMPARE function;
10. Next, this is the previous read data on Digiprog 3 but not the internal memory, comparing it with the EEPROM now re-inserted;

NOTE:

The error message may appear during the process, restore or reprogram, restore the initial state of data and it will be fixed.

Besides Digiprog 3 “EEPROM” Menu, there are also “AUTO / TRUCK” Menu, “Moto” Menu, “Special Functions” Menu and “Configuration” menu.

Case: Digiprog3 read&write Audi A4 eeprom HC12 mileage

Purpose:

copy the immo information from a cluster to another
make the mileage follow with the immo information

Model:

Audi a4 2001

Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA-USB programmer

Original cluster:

Digiprog 3 Manual 2015

The Jaeger cluster barely works

Suggestion:

read the pin code from both the Instrument and adapt it to the vehicle

What to do on pin 21 and 22 on the chip:

– With ECU programmers:

Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M, Carprog, UPA-USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

– with Digiprog3:

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

Problem & Solution: Digiprog3 Can’t Read EEPROM

Problem:

Used OBD ST01 & ST04 cables (contained in Digiprog 3 entire kit)to read EEPROM. The pic below shows what I did.

But the result can be seen like the following pic. The EEPROM cannot be read.

Solution:

1. Take down the clip and clear the chip. Then try it again.
2. If you do not want the clip,contact the purchasing specialist to ask for the 01/04 Adapter for Digiprog 3.

Looking for Digiprog 3 odometer correction tool user manual instructions? eobdtool.co.uk share here the instruction in English and German language.

Digiprog III user manual and pinout free download here:

Note: the above link is sponsored by eobdtool.co.uk.

DigiProg 3 user manual on dropbox:

The above links are large PDF files including all digiprog3 mileage tool workable vehicles as well as:

1) Wiring diagram including which cable/adapter to plug in

2) In what way should you done with the dashboard

3) Step-by-step procedure on how to correct mileage on each car makes.

4) DIGIPROG 3 cable pinouts text file

Pictures mean a lot.

The Digiprog user manual comes with default German language and English language.

2014 New digiprog 3 DP3 odometer master user manual on mediafire :

V4.94 digiprog 3review on what models work and what don’t work: